We will reply to your message within an hour.
Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.
Load material between the two halves of the ring and adjust the side bolts for a tighter fit than standard threaded-rod-mount clamping hangers.
Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.
Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.
These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.
Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.
Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.
Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.
Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.
Use these close-fitting hangers for a more rigid hold around material than when using straps alone.
Cut as much strap as you need to hang duct, pipe, and other materials.
Route pipe, tubing, and conduit across strut channel.
Hold pipe, tubing, and conduit away from strut channel.
Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.
For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.
Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.
For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.
Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.
Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.
A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.
Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.
A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.
Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.
Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.
Support vertical pipes passing through floors.
Use these clamps to route insulated pipe through floors. They have a plastic insert that creates a seal around the pipe's insulation to prevent the pipe from sweating, which can cause mold and corrosion.
Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.
A mounting plate provides a more secure hold at the mounting surface.
Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.
Also known as muffler clamps, these U-bolts have a rounded mounting plate that fully surrounds pipe, conduit, and tubing for a secure fit.
Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.
Suspend and route flat-bottomed objects such as strut channel and small duct.
Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.
Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.
Support strut channel at a right angle to the beam.
These OSHPD preapproved anchors and brackets support threaded-rod-mount hangers during seismic activity.
Mount to a surface to secure and route cable.
The tensile strength of these metric Grade B7 rods is about one and a half times higher than low-strength steel rods.
An economical alternative to Grade B7 and Grade B16 threaded rods, these metric Class 8.8 rods are suitable for fastening most machinery and equipment.
About half the strength of medium-strength steel threaded rods, use these for light duty hanging, mounting, and fastening.
These metric threaded rods are about half the strength of medium-strength steel threaded rods for light duty hanging, mounting, and fastening.
About half the strength of medium-strength steel threaded rods, use these metric fine-thread rods for light duty hanging, mounting, and fastening.
Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.
Ideal for environments that require frequent cleaning, such as food and pharmaceutical manufacturing, these rods have a removable cover that protects their threads from dirt and grime.
These steel studs are zinc plated to resist corrosion in wet environments.
Stick these studs to nearly any surface for a strong bond and a watertight seal.
These studs are also known as hanger bolts—use them to hang, mount, and fasten parts to wood structures.
Connect and separate threaded rods, studs, and other components. These hollow rods have internal threads on both ends, so you can make connections and still pass wiring and other objects through the center of the rod.
Mount a length of strut channel between the ends of a beam to run cable and conduit along the beam without drilling.
Attach strut channel at any point on a threaded rod without taking apart your assembly.
Designed for use with right-hand, internally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.
Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.
Create a choker loop around a supporting structure with the snap-hook end and use the loop to secure the suspended material.